Dongguan Runzhi Electronics Co., Ltd.

Products

Biochemical Incubator


Keywords :

Aging tester / Humidity Chamber / Floor tester


  • Hits : 13
  • Company : Dongguan Runzhi Electronics Co., Ltd.
  • Telephone : +86 13712847488
Contact Us

Product Details

Contact Us

Five Advantages Of Products

  • The chassis body is made of high-quality thin plates, and the surface coating is firm and beautiful.
  • A double-layer hollow glass window is installed in the middle of the box door, and the lighting inside the box is attached to make the test items clear at a glance.
  • The inner tank is made of mirror-finished stainless steel thin plate, four-corner arc-shaped processing, the temperature in the box is uniform, durable, and easy to clean.
  • The temperature control part adopts a new type of intelligent digital display temperature regulator with single-chip technology.
  • Users can set and adjust the temperature and time by operating the touch keys on the control panel according to different requirements to achieve the test purpose.

Product Details

The following is a biochemical incubator:

 

Product introduction: 

 

The biochemical incubator is a high-precision constant temperature device with cold and heat control. It can be used for plant cultivation, breeding experiments, cultivation and preservation of bacteria, molds, and microorganisms, BOD determination for water analysis, and constant temperature tests for other purposes. It is an ideal test equipment for scientific research units such as biological genetic engineering, medical treatment, sanitation and epidemic prevention, drug inspection, agriculture, animal husbandry and aquatic products.

 

Working principle of biochemical incubator:

 

The incubator converts the actual temperature sensed by the temperature sensor in the chamber into an electrical signal, and the microcomputer controls the heater or refrigeration compressor to work to achieve the desired temperature.

 

Technical parameters of biochemical incubator:

 

Nominal volume: 100L, 150L,250L

Temperature control range: 5-50℃

Temperature fluctuation tolerance: ±1°C (100L, 150L) ±1.5°C (250L)

Tolerance of temperature uniformity: ±1.5°C (100L, 150L) ±2°C (250L)

Power source voltage: AC 220V/50Hz

Input power: 280W (100L) 320W (150L,250L)

Working environment: ambient temperature 10~30℃ relative humidity below 70%

Refrigerant: R12

Equipment category: Type I and Type B

 

The temperature/time key can switch between temperature and time:

 

1. Temperature setting: Press the temperature/time key once, and the temperature setting indicator of the meter will be on. Press the set key to enter the SV state, one of the three numbers in the setting display window flashes, and then press the shift key (<) to move the flashing number to the desired setting position, and then press the ∨ or ∧ key to change the temperature setting Set the value to the required temperature (minimum value 0℃), press the set button after the last to save the set value into the single-chip microcomputer. At this time, the left display window displays the measured temperature, and the right display window displays the set temperature.

2. Time setting: Press the temperature/time key once, and the time setting indicator of the meter will be on. Press the set button to enter the TV state, one of the three numbers in the setting display window flashes, and then press the shift button (<) to move the flashing number to the desired setting position, and then press the ∨ or ∧ key to change the time setting Set the value until the required time (minimum value 1h), press the set button after the last to save the set value into the single-chip microcomputer. At this time, the left display window displays the measurement time, and theright display window displays the set time.

Timing function: When the instrument is powered on, the timing function starts. After the timing ends, the output is turned off. The heater and refrigeration compressor stop working, and the temperature in the incubator will gradually reach the ambient temperature.

3. Status indication: After the setting is completed, the equipment runs according to the set parameters. When the measured temperature is lower than the set temperature, the equipment enters the heating state and the heating indicator light is on. Conversely, when the measured temperature is higher than the set temperature, the refrigeration indicator light is on and the device enters the refrigeration state. When the measured temperature is 4°C higher than the set temperature, the alarm indicator will light up and the buzzer will beep.

4. Parameter modification: If you want to modify the temperature and time parameters during operation, follow procedures 1 and 2 to modify.

5. Quick setting: When setting parameters, one of the three digits flashes. If you press the ∧ key, the last digit of the setting value will increase by 1; if you press this key and hold it down, it will be set after about 3 seconds. The fixed value continuously increases by 1; if you press the ∨ key, the set value will decrease by 1; if you press and hold the key without releasing it, the set value will continuously decrease by 1 after about 3 seconds.

 

 

If you want to know more about the "biochemical incubator" or laboratory testing equipment related information, welcome to inquire!

 

Dongguan Runzhi Electronics Co., Ltd.

Contact Person:  Mr. Zheng

Department: Business Department

Post: Sales Manager

Telephone: +86 13712847488

Landline: +86 0769-81660769

Company Address: Room 101, 33 Zhenma Road, Dalingshan Town, Dongguan City, Guangdong Province,China

Factory Address: Room 101, No. 33 Zhenma Road, Dalingshan Town, Dongguan City, Guangdong Province,China

Website: www.instrumentvip.com

Previous: Salt Fog Tester

Next: Thickness gauge

Inquiry :

Inquiry